|
|
RC Relays |
|
40A continuous rating at 85°C
Plug-in and PC Board terminal
SPST
& SPDT configurations
Wash
tight and dust protected types available
Optional
mounting bracket
|
1. Contact Data
| Contact
Form |
1A |
1C |
| Contact
Rating |
14VDC
40A |
14VDC
30A(NO)/20A(NC)
G:40A(NO)/30A(NC) |
| Voltage
drop(Initial)1) |
Typ.
: 40mV (at 10A)
Max.: 250mV (at 10A) |
| Max.
Operating Current2) |
NO
: 120A NC
: 45A |
| Max Continous current |
NO : 60A (at 23°C)
NC : 45A
(at 23°C) |
| Min. contact load |
0.1A 6VDC |
| Life
Expectancy |
Electrical |
1x105 ops |
| Mechanical |
1x107 ops (300ops/min) |
| Initial
insulation resistance |
100MΩ |
Dielectric
strength
between3) |
contacts |
500VAC |
| coil and contacts |
500VAC |
| Operating time |
Max. 7ms (at nomi. vol.) |
| Release time |
Max.: 5ms4) |
| Temperature |
Ambient |
-40°C to 85°C |
| Storage |
-40°C to 155°C |
| Viberation resistance |
10Hz to 40Hz 1.5mm DA |
| Shock resistance |
98 m/s2 (10g) |
| Termination |
QC, PCB5) |
| Construction |
Wash tight, Dust protected |
| Unit weight |
Weather-proof cover : Approx. 55g
Others
: Approx. 35g |
| Mechanical data |
Cover retention (pull & push):245N
min.
Terminal retention (pull & push):100N min.
Terminal
retention to bending
(Front & side):10N min.
|
1) Equivalent to max. initial
contact resistance is 100mΩ (At 1A 6VDC)
2) Peak surge current
of lamp load under the voltage of 14VDC
3) 1 min, leakage current
less than 1mA
4) The value is measured when voltage drops suddenly
from nominal voltage to 0 VDC and coil is
not
paralleled with suppression circuit.
5) Since it is an environmental
friendly product, please select lead-free solder when welding.
The recommended soldering temperature and time
is 240°C to 260°C 2s to 5s.
2. Contact Data
Load
Voltage |
Load
Type |
Load
Current A |
On/Off
Ratio |
Electrical
endurance |
Contact
Material |
Ambient
temp. |
Loadwiring
Diagram |
| 1C |
1A |
On
sec |
Off
sec |
| NO |
NC |
NO |
| 13.5VDC |
Resistive |
Make |
40 |
30 |
40 |
1.5 |
1.5 |
1x105 |
AgSnO2 |
23°C |
See
diagram 1 |
| Break |
40 |
30 |
40 |
| Resistive |
Make |
30 |
20 |
40 |
1.5 |
1.5 |
1x105 |
AgNi0.15 |
| Break |
30 |
20 |
40 |
| Lamp |
Make |
120 |
- |
120 |
1 |
9 |
1x105 |
AgSnO2 |
23°C |
See
diagram 2 |
| Break |
20 |
- |
20 |
1) The load in the table excludes flasher. When
applied in flusher, a special ailver alloy(AgSnO2)
contact
material should be used
and the customer special code should be (170) as a suffix. please
heed the
anode and cathode's
request when wired, teminal 30 should connect with anode.
2)
Corresponds to the peak inrush current on initial actuation (cold
filament).
3)
The load wiring diagrams are listed below.
4) When the load requirement
is different from content oftable above, please contact HANDOUK
for relay
application support.
3. Coil Data
at
23°C
|
Norminal
voltage
VDC |
Pick-up
voltage
VDC |
Drop-out
voltage
VDC |
Coil
resistance
x(1±10%)Ω |
Parallel
Resistance
x(1±5%)Ω |
Equivalent
resistance
Ω |
Power
consumption
W |
Max.
allowable overdrive voltage2) VDC |
| 23°C |
85°C |
Weather
proof
cover |
6 |
3.6 |
0.6 |
22 |
--- |
--- |
1.6 |
10.1 |
7.9 |
| 6 |
3.6 |
0.6 |
22 |
180 |
19.6 |
1.8 |
10.1 |
7.9 |
| 12 |
7.2 |
1.2 |
90 |
--- |
--- |
1.6 |
20.2 |
15.7 |
| 12 |
7.2 |
1.2 |
90 |
680 |
79.5 |
1.8 |
20.2 |
15.7 |
| 24 |
14.4 |
2.4 |
360 |
--- |
--- |
1.6 |
40.5 |
31.5 |
| 24 |
14.4 |
2.4 |
360 |
2,700 |
317.6 |
1.8 |
40.5 |
31.5 |
| Others |
6 |
3.9 |
0.6 |
22 |
--- |
--- |
1.6 |
10.1 |
7.9 |
| 6 |
3.9 |
0.6 |
22 |
180 |
19.6 |
1.8 |
10.1 |
7.9 |
| 12 |
7.8 |
1.2 |
85 |
--- |
--- |
1.7 |
20.2 |
15.7 |
| 12 |
7.8 |
1.2 |
85 |
680 |
75.6 |
1.9 |
20.2 |
15.7 |
| 24 |
15.6 |
2.4 |
350 |
--- |
--- |
1.6 |
40.5 |
31.5 |
| 24 |
15.6 |
2.4 |
350 |
2,700 |
309.8 |
1.9 |
40.5 |
31.5 |
1) The power
consumption of parallel resistance is 0.5W
2) Max. allowable
overdrive voltage is stated with no load applied, illustrated with
dust cover version.
4. Ordering Code
5. Overall And Mounting Dimensions
|
