ID:     PW:   
Korean English
ȸ»ç¼Ò°³ Á¦Ç°¾È³» ±â¼úÀÚ·á °Ô½ÃÆÇ ÆǸŴ븮Á¡ »çÀÌÆ®¸Ê

Telecom
Power
General Purpose
Automotive
SSR(Solid State Relay)
Time
etc
Home > Product > Automotive    
    Socket Packing Cross Reference
Automotive
 
HANDOUK LOGO
RS Relays
 Micro miniature
 Silent type
 Two sets of seperated relay system
 Double relay
 RoHs & ELV compliant

CHARACTERISTICS

Contact arrangement 2 Form C
Voltage drop(initial)1) Typ.: 50mV (at 10A)
Max.: 250mV(at 10A)
Max. switching current 25A2)
Max. switching voltage 40VDC2)
Min. contact load 1A 6VDC
Mechanical endurance 1x107 ops (300ops / min)
Initial insulation resistance 100M¥Ø (at 500VDC)
Dielectric strength3)
between
Contacts : 500VAC
Coil and contacts : 500VAC
Operating time                  Typical : 3ms
                 Maximum : 10ms
Release time                  Typical : 1.3ms
                 Maximum : 10ms4)
Ambient temperature                                     -40°C to 85°C
Storage temperature                                     -40°C to 155°C
Viberation resistance 10Hz to 55Hz 1.5mm DA
55Hz to 200Hz 98m/s2(10g)
Shock resistance 294m/s2(30g)
Termination PCB5)
Construction Wash tight
Unit weight Approx. 15g

1) Equivalent to the max. initial contact resistance 100m¥Ø (at 1A 6VDC)
2) No contact, see "Local limit curve"
3) 1min, leakage current less than 1mA.
4) The value is measured when voltage drops suddenly from nominal voltage to 0 VDC and coil is not paralleled with suppression circuit.
5) Since it is ab environmental friendly product, please select lead-free solder when welding. The recommended soldering
    temperature and time is 240°C to 260°C, 2s TO 5s.

CONTACT DATA4)

Load voltage Load type Load current A On/Off ratio Electrical
life
Contact material Ambient temp. Load wiring diagram3)
2 C On
s
Off
s
NO NC
13.5VDC Simulate
motor
operation
Make1) 25 -- 0.02 3.6 1x105 AgNi0.15 85°C See
diagram1
Transient11) 15 -- 0.03
Transient21) 10 -- 0.03
Break 6 -- 0.032
Resistive Make 20 -- 1 3 2x105 AgSnO2 80°C See
diagram2
Break 20 --
Lamp2) Make 4x21W -- 1 5 2x105 AgSnO2 80°C See
diagram3
Break --

1) Current of turn on transient 1, transient 2 is subsection simulation to that of motor start-up peak value.

2) The load in the table excudes flasher, when applied in flasher, a special silver alloy (AgSnO2) contact material
    should be used and the customer special code should be (170) as a suffix. Please heed the anode and
    cathode's request when wired, common terminal should connect with anode.

3) The load diagram are listed below.

4) When the load requirement is different from content of the table above, please contact HANDOUK for relay application
    support.

COIL DATA

  Norminal
voltage
Pick-up
voltage
Drop-out
voltage
Coil
resistance
x(1±10%)
Power
consumption
Max. allowable overdrive voltage1)
23°C 85°C
Standard(RS/ST) 12VDC 7.2VDC 1.0VDC 255¥Ø 0.56W 20VDC 16VDC
Low pick-up voltage(RS/SPT) 12VDC 5.8VDC 0.8VDC 178¥Ø 0.81W 17VDC 13.5VDC

1) Max. allowable overdrive voltage is stated with no load applied.

ORDERING INFORMATION

OUTLINE DIMENSIONS, WIRING DIAGRAM AND PC BOARD LAYOUT

CHARACTERISTIC CURVES

Namkwang Centlex Room 412, 440-4 Cheongcheon-dong, Bupyeong-gu, Incheon 403-858, Korea.    E-Mail : sales@handouk.co.kr   TEL : 032-363-3800~4   FAX : 032-363-3805   Copyright 2009 @ HANDOUK Electronics Co. Ltd All Right Reserved.