ID:     PW:   
Korean English
ȸ»ç¼Ò°³ Á¦Ç°¾È³» ±â¼úÀÚ·á °Ô½ÃÆÇ ÆǸŴ븮Á¡ »çÀÌÆ®¸Ê

Telecom
Power
General Purpose
Automotive
SSR(Solid State Relay)
Time
etc
Home > Product > Automotive    
    Socket Packing Cross Reference
Automotive
HANDOUK LOGO

 RV9 Relays

 Features

 Extended temp. range up to 125°C
 SPST (1 Form A), SPDT(1 Form C) contact arrangement.
 2.8mm QC Terminals.
 RoHs & ELV compliant. 

Typical Applications Headlight control, Fuel pump control, Horn control, A/C compressor clutch

1. CONTACT DATA

Contact Arrangement 1 Form A, 1 Form C
Voltage drop (Initial)

NO: Typ.: 20mV, Max.: 250mV (at 10A)
NC: Typ.: 25mV, Max.: 250mV (at 10A)

Max. switching current8)

Make(NO): 100A2)
Break(NO): 30A(Resistive, 13.5VDC)
Max. continous current1),8) 30A(at 125°C, 1h)
Max. switching voltage See "Load limit curve"
Min. contact load 1A 6VDC
Mechanical endurance 1 x 107 (300ops/min.)
Electrical endurance See "CONTACT DATA"
Initial Insulation resistance 100M¥Ø (at 500VDC)

Dielectric strength3)

between contacts : 500VAC
between coil and contacts : 500VAC

Operate time8)

Typ.: 5ms Max. 10ms(at nomi. vol.)

Release time4).8)

Typ.: 3ms Max. 10ms3)
Viberation Resistance5),8)

10Hz to 40Hz 1.27mm DA
40Hz to 70Hz 49 m/s2
70Hz to 100Hz 0.5mm DA
100Hz to 500Hz 98m/s2

Flammability6)

UL94-HB or better(meets FMVSS302)
Shock resistance5),8) 196m/s2
Ambient temp. -40°C to 125°C
Unit weight Approx. 20g
Termination 2.8mm QC
Construction Plastic sealed, Dust protected
Mechanical data    cover retention (pull & push):200N min.
   terminal retention (pull & push):100N min.
   terminal resistance to bending(front&side): 10N min.7)

1) For NO contacts, measured when applying 100% rated voltage on coil.
2) Inrush peak current under lamp load, at 13.5VDC.
3) 1min, leakage current less than 1mA.
4) The value is measured when voltage drops suddenly from nominal voltage to 0 VDC and coil is not paralleled with suppression circuit.
5) When energized, opening time of NO contacts shall not exceed 1ms, when non-energized, opening time of NC contacts shall not exceed 1ms,
    meantime NO, contacts shall not be closed.
6) FMVSS; Federal Motor Vehicle Safety Standard.
7) Test point is at 2ms away from terminal end, and after removing testing force, the terminal transfiguation shall not exceed 0.5mm.
8) Only for the 12VDC coil voltage type.

2. COIL DATA   

Load
voltage

Load type

Load current A

On/Off ratio

Electrical endurance

Contact material

Load wiring diagram1)

Ambient temp.

1C

1A

On

Off

NO

NC

NO

13.5VDC Resistive Make 20A 10A 20A 2s 2s 1x105 AgSnO2 See
dia. 1
See ambient temp. curve
Break 20A 10A 20A
Lamp Make1 100A --- 100A 2s 2s 1x105 AgSnO2 See
dia. 2
Break 20A --- 20A
Inductive Make 40A

20A

40A 2s 4s 1x105 AgSnO2 See
dia. 3
Break 20A 10A 20A
27VDC Resistive Make 20A 10A 20A 2s 2s 1x105 AgSnO2 See
dia. 1
Break 20A 10A 20A

1) The load wiring diagrams are listed below (Rating of NO, NC are tested based on different samples separately.         

2) Loads mentioned in this chart is for relays with no paralled diode nor Zener Diode.
    For those with paralled diode, Zener Diode or other components, please contact HANDOUK for more technical suppots.
    please also contact HANDOUK if the actual application load is different from what mentioned aboved.

3. COIL DATA                                                                                                                       At 23°C

Norminal
Voltage
VDC
Pick-up
Volatage
VDC(Max.)
Drop-out
Voltage
VDC(Min.)
Coil
Resistance
x(+/-10%)¥Ø
Parallel
Resistance
x(+/-5%) ¥Ø
Equivalent resistance
    ¥Ø
Power consumption
W
Max.allowable overdrive vol. 1)VDC
at 23°C at 85°C
12 7.2 1.2 109 - - 1.3 20.4 14.9
12 7.2 1.2 109 680 93.9 1.5 20.4 14.9
24 14.4 2.4 360 - - 1.6 36 28
24 14.4 2.4 360 2,700 317.6 1.8 36 28

1) Max. allowable overdrive voltage is stated with no load applied.

4. ORDERING CODE

5. OUTLINE DIMENSIONS AND WIRING DIAGRAM

6. C H ARACTERISTIC CURVES

Disclaimer
The specification is for reference only. See to "Terminology and Guidelines" for more information. Specifications subject to change without notice. in case there is specific criterion (such as mission profile, technical specification, PPAP etc.) checked and agreed by and between customer and Handouk, this specific criterion should be taken as standard regarding any requirement on Handouk product.
We could not evaluate all the performance and all the parameters for every possible application. Thus the user should be in a right position to choose the suitable product for their own application. If there is any query, please contact Handouk for the technical service. However, it is the user's responsibility to determine which product should be used only.
                                        ¨Ï Handouk Electronics Co., Ltd.  All rights of Hnaouk are reserved

Namkwang Centlex Room 412, 440-4 Cheongcheon-dong, Bupyeong-gu, Incheon 403-858, Korea.    E-Mail : sales@handouk.co.kr   TEL : 032-363-3800~4   FAX : 032-363-3805   Copyright 2009 @ HANDOUK Electronics Co. Ltd All Right Reserved.