|
|
| HT6 Magnetic Latching Relay |
* 200A switching capability
* Strong resistance
ability to shock & vibration
* Low coil consumption, ultra-low temperature rise
* Low contact resistance
* Environmental
friendly product (RoHS compliant)
* Outline Dimensions(107.5 X 97.0X29.5)mm |
CONTACT DATA
| Contact arrangement |
2A / 2B |
| Contact resistance |
1.0mΩ (at 1A 24VDC) |
| Contact Material |
AgSnO2, AgCdO |
| Contact Rating(Res. load) |
200A
250VAC / 30VDC |
| Max Switching Power |
50,000VA |
| Mechanical endurance |
5 X 103ops |
| Electrical
endurance |
5 X 105ops |
CHARACTERISTICS
| Insulation
Resistance |
1,000MΩ, Min. at 500VDC |
Dielectric
Strength
|
Between coil& Contacts |
4,000VAC (for
one minute) |
| Between open& Contacts |
2,000VAC(for one minute) |
| Operate Time(at
nomi. volt) |
50ms max. |
| Release Time(at
nomi. volt) |
50ms max. |
| Ambient Temperature |
-40℃ to +70℃ |
| Shock
Resistance |
Functional |
100m/s2 (10g)
|
| Destructive |
1,000m/s2 (100g)
|
| Vibration
Resistance |
10-55Hz,
1.5mmDA |
| Humidity |
98%RH,40℃ |
| Ambient temperature |
-40% to 85% |
| Termination |
PCB & QC |
| Unit Weight |
Approx
.500g |
| Construction |
Dust proofed |
| Coil power |
Single Coil: 12W; Double Coil: 24 W |
COIL DATA
Nominal Voltage
VDC |
Pick-up Voltage
VDC |
Pulse Duration (ms) |
Coil Resistance(Ω) +/-10% |
| 12 |
906 |
≥150 |
Single Coil |
12
|
| 24 |
19.2 |
≥150 |
48
|
| 48 |
38.4 |
≥150 |
190
|
| 12 |
9.6 |
≥150 |
Double Coils |
6+6
|
| 24 |
19.2 |
≥150 |
24+24
|
| 48 |
38.4 |
≥150 |
95+95
|
Notes: When requiring
other nominal voltage, special order allowed.
NOTICE
1. Relay is on the “set” status hen being released
from stock, with the consideration of shock risen from transit and relay
mounting, relay would be changed to “reset” status, therefore, when
application(connecting the power supply), please reset the relay to “set” or “reset”
status on request.
2. In order to maintain “set” or “reset” status,
energized voltage to coil should reach the rated voltage, impulse width should
be 5 times more than “set” or “reset” time. Do not energize voltage to “set”
coil and “reset” coil simultaneously. And also long energized time (more than 1
min) should be avoided.
3. The terminals of relay without twisted copper wire
can not be tin-soldered, can not be mover willfully, more over two terminals
can not be fixed at the same time.
ORDERING INFORMATION
OUTLINE
DIMENSIONS AND WIRING DIAGRAM Unit:mm
Remark:1)
In case of no tolerance shown in outline dimension: outline
dimension≤1mm,tolerance should be±0.2mm;outline dimension〉1mm and
≤5mm,tolerance should be ±0.3mm；outline dimension >5mm
,tolerance should be± 0.4mm.
Remark: The
polarity of Reverse polarity and Standard polarity is opposite.
Disclaimer
This datasheet is for the customer’s
reference. All the specifications are subject to change without notice.
We could not evaluate all the
performance and all the parameters for every possible application. Thus the
user should be in a right position to choose the suitable product for their for
their own application. If there is any query, please contact HANDOUK for the
technical service. However, it is the user’s responsibility to determine which
product should be used only. |
