|
|
HT9 Relay |
* 60A switching capability
* 4Kv dielectric
strength (between coil and contacts)
* Heavy load up to 15,000VA
* Environmental
friendly product (RoHS compliant)
* Outline Dimensions(38.0X30.0X16.0)mm |
CONTACT DATA
Contact arrangement |
1A |
Contact resistance |
2m¥Ø (at 1A 24VDC) |
Contact Material |
AgSnO2, AgCdO, |
Contact Rating(Res. load) |
60A 250VAC : 5,000cperations, 50A 250VAC : 10,000operations,
40A 250VAC : 100,000operations |
Max
Switching Voltage |
250VAC |
Max Switching Current |
60A |
Max Switching Power |
1,5000VA |
Mechanical endurance |
1X106 ops, Meter :1 X105 ops |
Electrical
endurance |
1X105ops (at 40A250VAC) |
CHARACTERISTICS
Insulation
Resistance |
1,000M¥Ø, Min. at 500VDC |
Dielectric
Strength
|
Between coil& Contacts |
4,000VAC (for
one minute) |
Between open& Contacts |
1,500VAC(for one minute) |
Creepage distance |
8mm |
Operate Time(at
nomi. volt) |
20ms max. |
Release Time(at
nomi. volt) |
20ms max. |
Ambient Temperature |
-40¡É to +85¡É |
Shock
Resistance |
Functional |
98m/s2 |
Destructive |
980m/s2 |
Vibration
Resistance |
10-55Hz,
1.5mmDA |
Humidity |
98%RH,40¡É |
Ambient temperature |
-40% to 70% |
Termination |
PCB&QC |
Unit Weight |
Wash tight,Approx.33g |
Construction |
Wash tight, Dust proofed |
Coil power |
Single Coil: 1.0W; Double Coil: 2.0W |
Notes: When requiring
other nominal voltage, special order allowed.
SAFETY APPROVAL RATINGS
UL & CUL |
40A 250VAC at 70¡É 50A 250VAC at 70¡É 60A
250VAC at 70¡É |
Notes: Only some typical ratings are listed above. If more details are
required, please contact us.
COIL DATA
Nominal
Voltage VDC |
Pick-up
Voltage VDC |
Pulse
Duration ms |
Coil
Resistance¥Ø |
5 |
3.5 |
50 |
Single Coils |
24 |
6 |
4.2 |
50 |
35 |
9 |
6.3 |
50 |
80 |
12 |
8.4 |
50 |
145 |
24 |
16.8 |
50 |
575 |
48 |
33.6 |
50 |
2,270 |
5 |
3.5 |
50 |
Double Coils |
12+12 |
6 |
4.2 |
50 |
17.5+17.5 |
9 |
6.3 |
50 |
40+40 |
12 |
8.4 |
50 |
72+72 |
24 |
16.8 |
50 |
285+285 |
48 |
33.6 |
50 |
1,135+1,135 |
Notes: When requiring
other nominal voltage, special order allowed.
ORDERING INFORMATION
Notes : 1) Under the ambience with dangerous gas like H2S, SO2 or NO2, wash tight type recommended; Please test the relay in real applications. If the ambience allows, dust protected type is preferentially recommended.
OUTLINE
DIMENSIONS, WIRING DIAGRAM AND PC BOARD LAYOUT Unit:mm
HT9-**-**-1 HT9-**-**-2 HT9-**-**-3
HT9-**-**-4 HT9-**-**-5
Remark:
1)
In case of no tolerance shown in outline dimension : outline
dimension¡Â1mm,tolerance should be±0.2mm;outline dimension ¡µ1mm and
5mm, tolerance should be ±0.3mm£»outline dimension >5mm
,tolerance should be± 0.4mm.
2) The tolerance without indicating for
PCB layout is always ±0.1mm.
Note :
1. Melt both ends of the wire at
5mm, then weld it together with copper plate and relay Terminals(anti-tensile strength¡Ã50N)
2. Weld the copper plate with flex
wire, the anti-tensile strength should be 50N, please see The sketch map from right side
to left side
3. The welding direction of flex
wire should be orientated to state-spring.
4. ORDERING INFORMATION:
HT9-XX-ST-1-R A 50 / 80
Welding sketch map : A Type
The length of flex wire
- The length of right side flex wire L1 = 50mm :
- The length of right side flex wire L2 = 50mm :
Notes:
We can make special connection according to customer¡¯s requirement.
Please provide us with the drawing, and
shunt specification
Remark :
1) In case of no tolerance shown in outline dimension: outline dimension¡Â1mm, tolerance should be ±0.2mm; outline
dimension>1mm
and¡Â5mm, tolerance should be±0.3mm; outline dimension>5mm,
tolerance should be ±0.4mm.
2) The tolerance without indicating
for PCB layout always ±0.1mm.
Notice
1. Relay in on the "set" status when being released from stock, with the consideration of shcok risen from transit and relay mounting, relay would be changed to "reset" status, therefore, when application (connecting the power supply), please reset the relay to "set" or "reset" status on request.
2. In order to maintain "set" or "reset" status, energized voltage to coil should reach the rated voltage, impulse width should be 5 times more than "set" or "reset" time. Do not energize to "set" coil and "reset" coil simultaneously. And also long energized time (more than 1 min.) should be avoided.
3. The terminals of relay without flex wire can not be tin-soldered, can not be moved willfully, more over two terminals can not be fixed at the same time.
|